The Display Settings form allows you to set the various view display and property settings. The tabs on the Display Settings form give you access to specific areas of the views available.
The toolbar gives you the following options:
Open File - Locate and open an *.iddsx file that contains pre-set values for the Display Settings tabs.
Save File - Save the current Display Settings tab values to an *.iddsx file.
Default colours - Set the display colours for all items listed on the form to a predefined list of colours.
Default Deluge colours - Set the Deluge display colours to a predefined colour set.
This table dictates the visibility, display colour and object control of the listed layer items.
The layers can be filtered using the drop-down list above the table. This allows the table to be reduced to only showing the layers required.
The table dictates the visibility and colour of the listed layer items. The Colour Ramp dictates the colours of the Contours and Colour Fill that can be rendered for a given set of Surface Data.
|Items in this tab are only editable after a surface has been added to the current phase.|
The table dictates the visibility of the listed layer items.
The Colour Ramp dictates the colours of the Depth that can be rendered after Deluge analysis for a given set of Surface Data.
The Deluge water surface can be drawn as a series of independent grid levels (as analysed) or as a continuous surface. When Show Continuous Surface is selected, the grid level is applied at the centre of each grid square and the level linearly interpolated in between.
The Level of Detail slider allows you to specify the maximum number of grid squares that will be displayed along both axis of the Depth rendering.
|Items in the Deluge tab are only editable after a Deluge has been run.|
|Items in this tab are only editable after a Deluge has been run.|
The following fields are available in the Plan tab:
Text Height - Sets the text height on Plan.
Icon Height - Sets the maximum icon size when zooming on Plan.
Connection Line Width - Sets the line width used to render Connections (in pixels).
Grid Size - Sets the tick interval of the grid when shown on Plan.
Restore Plan view on Open - Sets the Plan to remember the view/zoom setting that was last used when re-opening.
Access Only or All Junctions - Decides what junctions are affected by the transparency slider.
Transparency Slider - Sets how transparent the objects appear on the Plan. The left-most side giving no transparency and the right-most side making them completely transparent.
The table dictates the colours of the items shown on profile view, both in the primary window and on the Plot Profile form.
The layers can be filtered using the drop-down list above the table. This allows the table to be reduced to only showing the layers required. Layers can be turned on and off by clicking the lightbulb icon in their row.
You can also modify the following fields:
Font Size - Sets the annotation and axis text font size on the Profile.
Summary Font Size - Sets the font size for the Summary table on the Profile.
The table dictates the display colours of the listed Flow Path items.
The following fields are available in the 3D tab:
Vertical Scale - Sets a scaling factor for the vertical axis in 3D. Available ratios are 1:1 (no scaling), 1:2 (vertical components twice as large as accurate values), 1:5, and 1:10.
Text Height - Sets the text height in 3D.
Icon Height - Sets the icon height in 3D.
Turn Off Simple Junctions - Enabling this option hides all simple junctions in 3D.
Table - Specify colour and visibility specific to 3D.
The following fields apply specifically to the surface.
Show - When checked, the surface is shown in the 3D window. When unchecked, the surface is not shown in the 3D window.
Use Colour Ramp - When checked, the surface will use the colours of the ramp as defined in the surface tab. When unchecked, the surface will use the colours of the triangles provided.
Wireframe - When checked, the surface will be a wireframe. When unchecked, the surface will be filled.
The colour ramp shows the blended ramp used for Surface Elevation/Deluge rendering. If no pegs are defined, the blend is between the end peg colours. End peg values and colours can be adjusted as described below but they cannot be deleted. Moving the mouse over the ramp will display the elevation value at the mouse position. Pegs can be used to introduce a colour change in the blend. See Add and Remove below for peg editing. Right-click the Ramp to display a menu also described below.
The drop-down menu provides several default colour ramps. Any of the colour ramps can be used with either Surface or Deluge. However, some are more appropriate than the others.
When blending the ramp between pegs, the control can blend the RGB (Red, Green, Blue) settings for the peg colours or the HSL (Hue, Saturation, Luminance) settings. Although the blending results can be very similar, the difference is more pronounced when blending ‘opposite’ colours e.g.: Green and Magenta.
Restrict to Maximum
If this checkbox is ticked, any value above the maximum value is not coloured on Plan.
If the checkbox is un-ticked, the maximum colour is used for all values equal to or above the maximum.
This field is the maximum value of the colour ramp. When used for the Surface, this value is set to the Maximum Z value from the surface.
Changing the value and/or the colour will update the Max peg. This field can be set to a value larger if required, but helper test at the bottom of the form shows the absolute maximum value.
Clicking the colour ramp will enter a value, appropriate to its position, in this field. The colour is set to the colour at the click position. Alternatively, you can enter a value and a colour. Clicking Add will add a new peg.
Clicking a peg will enter the peg details in this field. Changing the value and/or the colour will update the selected peg.
When a peg is selected, clicking Remove will delete the peg.
This field is the minimum value of the colour ramp. When used for the Surface, this value is set to the Minimum Z value from the surface.
Changing the value and/or the colour will update the Min peg. This field can be set to a smaller value if required, but helper test at the bottom of the form shows the absolute minimum value.
Restrict to Minimum
If this checkbox is ticked, any value below the minimum value is not coloured on Plan.
If the checkbox is un-ticked, the minimum colour is used for all values equal to or below the minimum.
Opaque – Transparent
Moving the slider sets the transparency of the colours on Plan. The transparency setting is not reflected on the ramp.
The right-click menu on the Ramp provides some simple adjustment actions.
Even Space Pegs - Evenly distributes the pegs on the ramp.
Narrow Space Pegs - Distributes the pegs with a bias towards the minimum.
Invert Space Pegs - Reverses the peg distribution.
Invert Colour Ramp - Reverses the ramp colours settings.
Double Pegs - Doubles the number of pegs. Typically when viewing contours, this option will double the number of contours.
Delete Pegs - Deletes all the intermediate pegs but not the end peg Min and Max settings